You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 29 Next »

Prerequisites:

Overview:

Transmission is an MQTT module for Ignition that can publish files using MQTT Sparkplug to be processed by MQTT engine. 

Files are transferred using Sparkplug over MQTT and which files get transferred and when they get transferred can be configured in a number of different ways. The file transfer configuration also defines how quickly a file transfer occurs and how long before a timeout will occur on failure to receive host side acknowledgements which can be adjusted as required based on the size of files you are sending and any bandwidth constraints that you may have.

This tutorial shows how to configure the MQTT modules to manually publish and process files.

Step 1: Install the MQTT modules

Install the three MQTT modules listed in the pre-requisites onto your Ignition system following the Cirrus Link Module Installation guide.

By default, both MQTT Engine and MQTT Transmission are configured to connect to MQTT Distributor on tcp://localhost:1883 and will show as Connected under their respective Servers configuration setting in the Ignition UI. MQTT Transmission will also have an Example Transmitter configured pointing to a set of tags that are configured in the Ignition "default" tag provider. 

Review the MQTT Transmission Transmitters and Tag Trees tutorial for additional information on how Transmitter configurations interact with Ignition tag trees to create the Sparkplug IDs required.

This allows the three modules to automatically connect and provide a starting base for the tutorial.

Step 2: Configure Primary Host on MQTT Engine and MQTT Transmission

Navigate to the MQTT Engine > Settings in the left side of the Ignition Gateway UI and select the General tab.

Set Primary Host Enabled and add a Primary Host ID as shown below:

Navigate to the MQTT Transmission > Settings in the side of the Ignition Gateway UI and select the Sets tab.

Edit the Default Set and add a Primary Host ID as shown below:

Step 3: Config MQTT Engine File Handling

Now we can configure the MQTT Engine module to process the published files.

Navigate to the MQTT Engine > Settings in the left side of the Ignition Gateway UI and select the Namespaces tab. From the Default tab, edit the Sparkplug B namespace shown below:

Now select the 'Files' tab and set the following

  • Ignore Files
    • Set this property to unchecked so that publish files will not be ignored
  • File Host Type:
    • ACTIVE to specify that a message ACK is sent back to MQTT Transmission
  • Base File Directory
    • Set to some directory file path (i.e. 'C:\My Files' or something similar) where the files will be stored
  • Add Topic Tokens
    • Leave this property as checked to add the Group ID, Edge Node ID and Device ID to the base file directory path
  • File Storing Policy
    • Set this policy to REPLACE_EXISTING_FILE
  • File Attributes Policy
    • Leave this property at the default value of IGNORE
Review the MQTT Engine Configuration guide for information on all the File properties

When complete, it should look similar to the following. Save the changes after confirming.

Step 4: Configure MQTT Transmission to publish files

Now we can configure the MQTT Transmission module to publish files using a configured Transmitter. Navigate to the MQTT Transmission > Settings in the left side bar of the Ignition Gateway UI and select the Transmitters tab.

Make note of the Sparkplug IDs configured for your transmitter. For our example we have the Group ID as My MQTT Group and the Edge Node ID as Edge Node faec7e

Now on the  'Files' tab, select the Create new Files... link and configure the following fields

    • Name
      • By default a unique name will be set for this File Record. You can edit this if you choose but it must be unique.
    • Tag Provider
      • Set to 'default'. This is the tag provider where the publish control and information tags will be created
    • Tag Folder Path
      • Set to 'files_manual'. This is the tag folder in the specified tag provider where the publish control and information tags will be created
    • Enable Auto-Publish
      • Leave this unchecked. This will force manual publishes only  
    • Group ID
      • Use the Group ID from your Transmitters Sparkplug ID. For this example, My MQTT Group
    • Edge Node ID:
      • Use the Edge Node ID from your Transmitters Sparkplug ID. For this example, Edge Node faec7e 
Review the MQTT Transmission Configuration guide for information on all the File properties

When complete, it should look similar to the following. Save the changes after confirming.

After the configuration is saved, it should look similar to below:

Step 5: Publish Files

At this point, everything should be configured to send files from MQTT Transmission to MQTT Engine. Open Ignition Designer on the system running MQTT Transmission. You should see the control and information tags created in the specified tag provider and folder as shown below:

At this point, we just need to tell MQTT Transmission which file to send. Download this sample_file.zip which contains two text files. The two text files are:

  • sample_file.txt

    • This is a text file with an arbitrary string. But, it could be a file of any type. This is purely for demonstration purposes.

  • sample_file.txt.md5

    • This is a text file that contains only the md5 sum of the sample_file.txt


Certain characters have special meanings when used in filenames such as "*" for wildcards, and "\" in filename paths. If a file you are trying to publish contains any of the characters listed below, it will prevent files from being written to the file system.

" * : < > ? / \ |

Leading and trailing spaces in filenames and filenames ending in '.' are also not supported.


Unzip this sample file to some location and note that location. When transferring any file, MQTT Transmission requires two files to be present before it will transfer the target file. The first is the file itself. The second is a file that has the same name as the target file followed by a '.md5' extension. The contents of that file must contain the Message Digest Algorithm 5 (or MD5 sum) of the file. The MD5 sum can be calculated using command line utilities on most operating systems. Here are some examples:

Linux

ubuntu@linux-host:~$ md5sum myfile.bin
07180622a24ebf905cf5f770cd54197a  myfile.bin

# In the above example, the md5 sum is: 07180622a24ebf905cf5f770cd54197a

OSX

user@osxhost:~$ md5 sample_file.txt
MD5 (sample_file.txt) = 85324ffbcc7d97c478adf53796aff787

# In the above example, the md5 sum is: 85324ffbcc7d97c478adf53796aff787

Windows

Get-FileHash -Algorithm MD5 .\some_file.iso

Algorithm       Hash                                                                   Path                                                                              
---------       ----                                                                   ----                                                                              
MD5             80FD169D3FDADBC97E66C168F796B1BF                                       C:\temp\some_file.iso

# In the above example, the md5 sum is: 80FD169D3FDADBC97E66C168F796B1BF


With both files in place, we can now set the 'Publish File Path' tag.

This path must be the full path to the target file to publish over MQTT. In this example, we're using the path of '/tmp/transmission/sample_file.txt'. However, on a Windows system that would look something like 'C:\full\path\to\my\sample_file.txt'. When this is set, you should see something like this

Finally, click the 'Publish File' boolean tag. This will begin the file publish process which will cause the file to be published. After doing so, you should see something similar to what is shown below.

You should also now see the file to the location you set as the 'Base File Directory' in your MQTT Engine namespace configuration for Sparkplug B.

With the File Auto_Publish disabled, the files will be left on the originating filesystem after a successful publish and will need to be removed manually


Step 6: Viewing the messages in the Ignition logs

The records published from MQTT Transmission can be be viewed in the Ignition Gateway logs by setting the com.cirruslink.mqtt.engine.gateway.sparkplug.SparkplugPayloadHandler logger to TRACE.

Review the Gateway Loggers from Ignition for details on how to do this.




Extra Activities

At this point you have a fully functional system which can be expanded or modified as required. Below are some addition configuration options to try:

Setup MQTT Transmission to automatically publish files

Create a new File record following Step 4 in tutorial checking the 'Enable Auto-Publish' and configuring the Tag Folder Path to "files_auto".
With auto-publish enabled, MQTT Transmission will create a tag called 'Publish Files Folder' instead of 'Publish File Path' as shown below.
MQTT Transmission will scan the folder specified in the tag, with a frequency defined by the File Scan Rate, and publish all files that appear in this directory automatically. When the file is successfully transferred both the file and associated md5 sum file will be removed from the originating filesystem.

Just as with the 'manual publish' option, an associated md5 sum file must be present and properly represent the md5 sum of the target file before it will be published.

Adjust the file transfer configuration to define how quickly a file transfer occurs and how long before a timeout will occur on failure to receive host side acknowledgements based on the size of files you are sending and any bandwidth constraints that you may have.

Setup two Ignition systems - a host system installed with MQTT Engine and MQTT Distributor and and edge system installed with MQTT Transmission

By default, MQTT Transmission is configured to connect to MQTT Distributor on tcp://localhost:1883. As the MQTT Distributor is installed on a different server, we will need to edit the configuration to allow MQTT Transmission to connect to the host server.

The MQTT Server must be accessible to the Ignition system running MQTT Transmission. In order for this to work port 1883 must be open to outside connections. Make sure this is allowed via your operating system's firewall configuration and any anti-virus software you may have installed.

This configuration is not recommended for production systems. If running this in production, you should be using TLS encryption on port 8883. More information on how to configure TLS can be found here.

Navigate to the MQTT Transmission > Settings in the left side bar of the Ignition Gateway UI and select the Servers tab.

Change the server URL to point to the server IP address or domain name of the Ignition system running MQTT Distributor and save the configuration.





Additional Resources

  • No labels

New to MQTT? Start Here!